E26 Lamp Holder vs E27: UL and CE Sourcing Guide for OEM

E26 Lamp Holder vs E27: UL and CE Sourcing Guide for OEM

E26 lamp holder or E27? Thread, voltage, UL 496 and IEC 60238 differences, plus an incoming-inspection checklist for OEM buyers sourcing lamp holders.

An E26 lamp holder and an E27 lamp holder look almost identical on a sample tray. The threads differ by about one millimetre, and a lamp will often start in both. That is why this spec goes wrong on purchase orders. The two bases belong to different voltage systems and different certification routes. A part that screws in cleanly can still fail your safety file.

This guide is for the sourcing engineer who approves the base, the body grade and the test report before tooling is released. Short on time? Read the table and the checklist.

Quick answer: E26 or E27 for your market

Spec item: Thread diameter; E26 (medium base): About 26 mm; E27 (Edison screw): About 27 mm

Spec item: Mains system; E26 (medium base): 100–127 V; E27 (Edison screw): 220–240 V

Spec item: Main markets; E26 (medium base): North America, Japan; E27 (Edison screw): Europe, Asia, Africa, LATAM

Spec item: Product standard; E26 (medium base): UL 496 / CSA C22.2; E27 (Edison screw): IEC 60238 / EN 60238

Spec item: Approval route; E26 (medium base): Listing + factory follow-up; E27 (Edison screw): CE + technical file

Spec item: Certified substitute?; E26 (medium base): No; E27 (Edison screw): No

Mechanical fit is not electrical approval. Confirm limit values against the current edition of the standard with your own laboratory before you freeze a drawing.

Thread and gauge: why the bases are not interchangeable

The Edison screw family is defined by thread form, major diameter and gauge acceptance, not by how the part feels in your hand. An E26 shell is gauged to a smaller envelope than an E27 shell. A worn or under-sized E27 shell will accept an E26 lamp and pass a casual assembly check. Contact pressure then drops, resistance rises, and the joint runs hot.

Ask for three records on every lot: go / no-go gauge results for the shell, thread engagement depth, and centre-contact protrusion. A gauge record costs minutes. A loose shell in a sealed ceiling fitting costs a recall.

Watch mixed-territory SKUs too. A fixture sold in both the US and Europe needs two part numbers, two test files and two carton labels.

Certification path: UL for North America, CE for Europe

For North America, lampholders are evaluated to UL 496 (https://www.ul.com/), with the Canadian counterpart under CSA C22.2. What you need is a recognised component listing your finished luminaire file can reference. Listing carries ongoing factory follow-up inspection, so construction changes must be reported.

For Europe and most 230 V markets, the reference is IEC 60238 (https://webstore.iec.ch/) for Edison screw lampholders, with the harmonised EN version supporting the CE technical file. Here the manufacturer and importer hold the test evidence. There is no listing database to hide behind.

The difference for a buyer is documentation depth. A UL-recognised E26 lamp holder gives you a traceable file and a controlled construction. A CE-marked E27 part gives you a report you must read. Check the edition, the rated voltage and temperature, and that the body material in the report matches the part you receive.

Failure modes that show up after twelve months

Most lampholder claims are not launch failures. They arrive after one heating season.

1. Shell loosening. Thermoplastic creeps under thread load at temperature. Pressure falls and arcing starts.

2. Terminal back-out. Untested screw terminals relax after thermal cycling and overheat.

3. Centre-contact collapse. A thin spring contact takes a permanent set, so the lamp flickers.

4. Body embrittlement. UV and heat chalk a bright housing; it cracks at the next lamp change.

5. Wrong temperature grade. A T150 part in a T210 fitting discolours, then deforms.

6. Plating failure. Thin nickel or bare brass corrodes in humid markets, raising thread resistance.

Each is a design or grade decision, not bad luck. Ask which of them the supplier has tested for.

Incoming-inspection checklist before you release the PO

Run this on pre-shipment samples, then repeat it on the first bulk lot.

1. Shell go / no-go gauge, recorded per cavity.

2. Centre-contact protrusion and spring force.

3. Terminal torque, re-measured after heat ageing.

4. Conductor pull-out force on both terminals.

5. Temperature rise at rated load in the worst-case enclosed fitting.

6. Temperature marking on the body, matched to the fixture.

7. Ball pressure and glow-wire results for the exact body grade.

8. Insulation resistance and dielectric strength after damp heat.

9. Report cross-check: edition, voltage, T-rating, material grade.

Ask for results per grade and per lot. A resin vendor's datasheet is not evidence about your part.

What this means when you order from Aotai

We build both bases. Zhejiang Aotai Electronics has made wall switches, sockets, plugs, E27 and E26 lamp holders, junction boxes and power strips since 1983, with CE, UL and RoHS compliance supporting exports to more than 30 countries.

Tell us the destination market, the fixture's internal temperature, the lamp wattage and whether the socket is enclosed. We quote the base, body grade and T-rating that survive those conditions, not the cheapest part that screws in. See the lamp holder and wiring accessory range (https://www. chinaaotai.

com/products), how our moulding and assembly lines run (https://www. chinaaotai. com/manufacturing), and what our quality control covers (https://www. chinaaotai. com/quality). More notes are in News (https://www. chinaaotai. com/news), or send us a drawing (https://www. chinaaotai. com/contact).

FAQ

Can I use an E27 lamp holder in a 120 V product?

It may work electrically, but certification does not transfer. A North American file expects a construction evaluated to UL 496. Substituting an IEC-only part invalidates the luminaire listing.

Is an E26 lamp holder the same as a "medium base"?

Yes. Medium base is the North American name for the E26 screw size. Candelabra and mogul are different sizes again.

Do E26 and E27 need different tooling?

The shell and body cavity differ, so plan on separate tooling or inserts. Sharing a shell across both bases is a common source of gauge failures.

What documents should I ask for before the first order?

The product test report, material grade declaration, RoHS evidence, gauge records and a sample approval sheet. Ask for the report edition, not a certificate image.

Written by the AOTAI technical team. Zhejiang Aotai Electronics manufactures wall switches, sockets, plugs, lamp holders, junction boxes and power strips for export markets since 1983.

All news and guides