A Schuko power strip looks like a commodity until two quotes land side by side. One is 16 A with individual switches and a fuse. The other is 10 A with a master rocker and a surge module. Both show CE. Both pass a casual sample check. Only one survives your market's load profile and your customer's warranty window.
This guide is for the buyer or OEM engineer who freezes the configuration before tooling and packaging are printed. Short on time? Read the table and the audit checklist.
Figure: White five-outlet Schuko power strip with red master rocker and coiled cord on a factory inspection bench beside a caliper and torque screwdriver (https://www.chinaaotai.com/uploads/tenant-1/f00f0c916ad3bd58bde5d7c18b931fdd.jpg)
Quick answer: which Schuko power strip to spec
Configuration: Master rocker, 5–6 way; Best suited to: Budget retail, whole-board shutdown; Verify before PO: Switch rating against total load; Aotai reference: Five-way 16 A board
Configuration: Individual switches, 3–4 way; Best suited to: Desk, kitchen, rental property; Verify before PO: Per-socket switching, lit rockers; Aotai reference: Three-way with USB
Configuration: USB-C integrated; Best suited to: Office and hospitality desks; Verify before PO: Shared versus per-port wattage; Aotai reference: Twin Type-C strip
Configuration: Surge protected; Best suited to: Electronics-heavy loads; Verify before PO: MOV rating and thermal disconnect; Aotai reference: Six-way 2-way surge
Configuration: Fused master board, 10 A; Best suited to: Markets expecting a fuse; Verify before PO: Fuse rating and replacement access; Aotai reference: Six-way fused board
The reference column maps to live SKUs in our EU and Schuko range (https://www.chinaaotai.com/products). Confirm limit values against the current edition of the applicable standard with your own lab before you freeze a drawing.
Master rocker or individual switches
A master rocker switches the whole board with one contact set. It is cheaper, simpler and easier to seal. Individual switching puts a rocker per socket, so a fault or a standby load can be isolated without pulling plugs.
The cost difference is not only the rockers. Each switched socket needs its own contact path and terminal space, which lengthens the busbar and the housing. Ask whether the quoted price includes lit rockers, because an indicator adds a leakage path and one more part to fail.
For rental and hospitality projects we usually quote individual switching. For price-driven retail, the five-way master board (https://www.chinaaotai.com/products/schuko-five-way-lead-red-master-rocker-16a) is the honest answer.
Overload protection is not surge protection
These are different functions and different parts. A fuse or thermal breaker opens on overcurrent. It protects the cord and the busbar from too much load. It does nothing to a voltage spike.
A surge module uses MOVs to clamp transients, and it ages with every event it absorbs. Ask for the clamping behaviour, the nominal discharge current and the thermal disconnect, evaluated to the SPD standard such as IEC 61643-11. A joule number on a carton is marketing, not a test result.
Our six-way surge block (https://www.chinaaotai.com/products/eu-6-outlet-extension-block-2-way-surge) and the fused master board (https://www.chinaaotai.com/products/eu-6-outlet-power-board-master-switch-fuse) are different products for different risks. Do not let a quotation substitute one for the other.
USB-C in a strip is a thermal question
A USB-C port is a small power supply inside your enclosure. The number that matters is not the peak wattage on the box. It is the sustained output with every port loaded, at your ambient temperature.
Ask three things. Is the wattage shared or per port? Which PD profiles are negotiated? What happens thermally at full load for one hour? A module that folds back to half power after ten minutes will generate returns that look like socket faults.
Request the charger module's own safety report to IEC 62368-1 as a separate document. Our three-way strip with two USB-A and one Type-C (https://www.chinaaotai.com/products/eu-3-socket-strip-independent-switches-usb) states the port mix on the drawing, not on the carton.
Cord, plug and rating: three numbers
The cord cross-section, the plug standard and the rated current must agree. A 16 A board on a 1.0 mm² cord is a heating problem waiting for a kettle. Typical builds use 3G1.5 mm² for 16 A and 3G1.0 mm² for 10 A; confirm against the cord standard and your market.
Schuko earthing runs through side clips, not a pin. Check clip spring force and contact resistance, because a weak clip reads as a warm socket after a year. Strain relief at both ends is a pull-test item, not a cosmetic one.
Certification: CE, SASO and UKCA do not transfer
For the EU, the socket-outlet requirements sit in IEC 60884-1 (https://webstore.iec.ch/), with the harmonised EN version supporting the LVD file and the CE declaration. The cord set and any surge or USB module carry their own evidence.
Gulf destinations may require SASO conformity documentation on top of CE; some of our strips carry it and some do not, per model. UK variants need UKCA and BS 1363 construction, which is a different socket entirely. A North American re-badge moves you to relocatable power taps under UL 1363 (https://www.ul.com/).
Read the report, not the certificate image. Check edition, model coverage, rated current and the housing material named in the report.
Failure modes after one heating season
1. Earth clip relaxation, then a warm socket under load.
2. Rocker contact welding on an inductive load.
3. Wrong fuse rating fitted at repair, defeating protection.
4. MOV ageing with no thermal disconnect.
5. Cord pull-out at a strain relief that was never pull-tested.
6. USB fold-back mis-sold as full wattage.
7. Housing chalk and crack where a PP grade replaced PC.
Each is a specification decision. Ask which of them your supplier has tested.
Factory audit and incoming inspection
On the audit, walk the line in order: stamping, injection, assembly, test, pack. Confirm the contact clips and busbar are formed in house, and that every finished board passes dielectric and earth-continuity test, not a sample.
On incoming lots, check socket gauge and clip force, rocker function per socket, cord pull and flex, rating label against the report, and USB output at full load. Record results per lot. Our quality control (https://www.chinaaotai.com/quality) and manufacturing (https://www.chinaaotai.com/manufacturing) pages describe what we run; more notes sit in News (https://www.chinaaotai.com/news).
Ordering from Aotai
Zhejiang Aotai Electronics has made wall switches, sockets, plugs, E27 and E26 lamp holders, junction boxes and power strips since 1983, with CE, UL and RoHS compliance supporting exports to more than 30 countries. Power strip MOQ is 500 pcs per model, with drawings and samples on request.
Tell us the destination market, the expected load and whether the board feeds electronics or heaters. We quote the configuration that survives it. Send us your specification (https://www.chinaaotai.com/contact).
FAQ
Is a Schuko power strip 16 A or 10 A?
Both exist. The rating follows the cord, the busbar and the plug, not the socket count. Read the label and the report together.
Does CE cover the USB charger inside?
No. The charger module needs its own safety evidence. Ask for it as a separate document.
Can I add surge protection to an existing quoted board?
Only as a construction change. The MOV module changes spacing, thermal behaviour and the test file. Re-quote and re-test.
Do you support private label and custom packaging?
Yes, within the certified construction. Changing the housing material or the contact system restarts testing.
Written by the AOTAI technical team. Zhejiang Aotai Electronics manufactures wall switches, sockets, plugs, lamp holders, junction boxes and power strips for export markets since 1983.